Flat roof system III Long side
Clamping on the long frame side of the modules for maximum loads
- Maximum utilisation of the roof surface and evenly distributed electricity production
- Efficient use of space thanks to 10° module inclination and landscape installation
- Cross connections at module field edges for high stability
Your benefits
Clamping of the module in the optimum area of the long frame side for maximum wind and snow loads, especially with large modules
Low logistical effort and optimal handling thanks to short components
Simple and quick installation due to high degree of pre-fabrication and tool-free click system
Wind tunnel tested aerodynamics
Components
Components
Click on the + Icons to see components of this mounting system.
Base element e/w 690 mm
- wide and continuous base troughs for optimum load redistribution and low surface pressure
- much space for ballast, optionally ballast trough available
- top cover when used as a cable channel
Features
Flat roof
Alu / A2SS / PE
Flat roof system III east-west
for click-fit of the module supports and connection of connector and edge closure sets
690 x 150 x 40 mm
995 - 1070 mm
03-001536
Base element e/w 840 mm
- Completely pre-assembled
- toolless clickfit of module supports
- toolless mounting of connector and edge closure sets
Features
Flat roof
Alu / A2SS / PE
Flat roof system III east-west
for click-fit of the module supports and connection of connector and edge closure sets
840 x 150 x 40 mm
1071 - 1145 mm
03-001537
Connector set e/w 1940 mm
- Completely pre-assembled with integrated base feet
- toolless mounting
Features
Flat roof
Alu / A2SS / PP
Flat roof system III east-west
connection of two base elements east-west, front module support in installation middle areas.
1940 x 147 x 101 mm
03-001533
Edge closure set 970 mm
- Completely pre-assembled with integrated base foot
- Toolless mounting
Features
Flat roof
Alu / A2SS / PP
Flat roof system III east-west
front module support and closure at module field edges
970 x 147 x 101 mm
03-001532
Flat roof end clamp
- screw with drill bit for easy assembly
- entirely pre-assembled
- only two clamps for all frame heights (can also be used in the novotegra Flat roof II system with third base trough)
Features
clamping system
landscape
flat roof system II east-west and south
clamping long frame side
30-42mm, 43-52mm
14x52mm
03-000396;03-000397
Support brace | Flat roof III
- load transfer between modules
- ballast reduction through system coupling
Features
2,00m, 2,40m
clamping system
landscape
flat roof east-west single-layer, flat roof III east-west
cross bracing of the system
20x20x1,5mm
03-001680; 03-001530
Module support 10° Long side
- tool-less clickfit into the base element
- with integrated holder for cable channel and mountingset optimizer FR
Features
Clamping system
Landscape
Flat roof III Long side
Rear module support
289 x 60 mm
03-001550
Accessories
Downloads
Mounting tutorial
How to easily mount our mounting system.
Module approvals
| Manufacturer | Module | Flat roof II / Flat roof III | Flat roof II with 3rd base trough | Insertion system portrait | Insertion system landscape | Insertion system portrait with support rail | Status | |||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Suction | Pressure | Suction | Pressure | Suction | Pressure | Suction | Pressure | Suction | Pressure | |||
The specified values (given in Pascal (Pa)) correspond to the permissible load. The safety factor of 1.5 to be considered according to IEC 61215 is already included. To the best of our knowledge and conscience, we have compiled the listed data for you from the individual approvals or installation instructions of the manufacturers. We accept no liability for transmission errors or changes to the values at short notice.
