Metal tile roof | clamping system portrait
Clamping system with direct fixing and modules installed in portrait
- Module clamping in the optimum clamping range
- Reduced logistical effort on the roof
- Quick and efficient mounting from above
- Electrically conductive connection between the mounting system and the roof membrane
Your benefits
Only a handful of components, entirely pre-assembled
Low material costs and easy handling
High holding forces thanks to chipless direct fixing with building authority approved thin sheet screws
Only one mounting tool necessary
Components
Components
Click on the + Icons to see components of this mounting system.
Middle clamp blank/black
- easy to mount thanks to locking function
- little space required
Features
clamping system
portrait & landscape, single-layer or cross rail connection (depending on the roof type)
C-rail/ C-N-rail, short rails, Flat roof III
30-42mm/43-52mm
11.4mmx52mm
yes
03-001345/03-001346/03-000285/03-000286
End clamp blank/black
- easy to mount thanks to locking function
- little space required
- flush termination with the rail possible
Features
clamping system
portrait & landscape, single-layer or cross rail connection
C-rail/ C-N-rail, short rails, Flat roof III
30-42mm/43-52mm
14mmx52mm
yes
03-001237/03-001236/03-000287/03-000288
Slip guard
- mounting aid for placing the modules
- additional securing of modules
Features
clamping system
portrait
C-rail/C-N-rail/N-rail/module support rail green roof
M8, M6, without hole
25mm
03-000006/03-000007
Short rail C24 with EPDM 385mm
- entirely pre-assembled with EPDM-sealing and perforations
- flexible positioning trough perforations
- material-saving fixation
Features
can be used as module support rail
portrait
high
module clamps
24x52mm
385mm
-
03-001081
Short rail C47 with EPDM 385mm
- entirely pre-assembled with EPDM-sealing and perforations
- flexible positioning trough perforations
- excellent module rear ventilation with extra space to
the roof covering
Features
can be used as module support rail
portrait
high
module clamps
47x52mm
385mm
-
03-000873
End cap C-rail C47
- visually attractive rail finish
- UV- and weather resistant
Features
clamping system
not necessary
C-rail 47
57x63x80mm
End cap C38 sw
03-001522
Mounting screw E16
- high holding forces thanks to chipless direct fixing
- building authority-approved thin sheet screws
Features
thin sheet metal screw V2A with EPDM seal
6.0x25mm
16mm
03-000880
Mounting screw E11
- high holding forces thanks to chipless direct fixing
- building authority-approved thin sheet screws
Features
thin sheet metal screw V2A with EPDM seal
5.5x25mm
11mm
03-000893
More information about the metal roof mounting system
Our system variants - your choice! The variant with the short profiles C24 and C47 allows you easy handling on site thanks to pre-assembled components. Our mounting system for modules in portrait meet every requirement. When assembling on short rails, you use our 385 mm long, pre-punched module support profiles pre-assembled with EPDM seal.
The short profiles can be adjusted flexibly to all common metal tile sheets and are available in two different heights. With the C24 short profile, you get a material-saving and economical solution for your projects. Or you can use the short profile C47 and you get an ideal rear ventilation of the modules due to sufficient space to the roof covering. No matter how you decide, you will always make the right choice with our short profile variants!
To meet your requirements of neat cable routing, you can also use the short profiles as a cable channel. Both short profiles are mounted with already glued EPDM sealing strips over two high beads.
Downloads
Mounting tutorial
How to easily mount our trapezoidal metal roof clamping system.
